Flytec 5030 v2.24 * Manual de usuario descargar pdf (Pagina 31)

Flytec 5030 GPS

Airspeed Offset This value will be added or subtracted to

the actual speed value. This value can be

used to compensate the slower airsflow

under the airfoil

Vario audio threshold Fine tuning of climbing tone max 20 cm 2 cm/sec

Pilot name Pilot name entry; max 25 letters not set

Speed mode TAS or IAS; upper or lower range 1.4; 5.3 0 = true airsp.

Units Meter or feet; Km/h or mph or knots

Temp.: In Grd C or Grd F; Km or miles

m ; km/h ;

Grd C; Km

Init EEPROM Back to factory settings 3.1 No

Erase all records Deletion of flight memory (all records) This

command formats the flight memory if an

error in the memory occurred. The settings

remain unchanged

3.2 no

Erase all WP& routes Deletion of all WPs and Routes 3.3; 3.4 no

Init GPS Entry of posit. for faster satellite reception

Set of a geodetic map system

2.1

2.6; 6.2

actual position

1 = WGS84

Coordinate Format * dd°mm,mmm or dd,ddddd or dd°mm'ss”

UTM ; Suisse Grid #

dd,mm,mmm

Recording mode Autom. or manual flight recording 3.2 Aut.

Average thermal

climb

Time delay for average climb in the

thermals

1.10 0,5…10 min

10min

Glider type Name of glider for OLC not set

Glider ID Glider registration for OLC not set

McCready

Tone gap

Delay for McCready acc. to climb

Acoustic dead band in +/- xx cm/sec

1.9 7 seconds

30 cm/sec

Vario Display Circle scale or bar scale 1.1 Yes = circle

Userfields 3 user selectable pages with 6 normal or 4

large fields

1.7 Yes = 6 fields

Init CTRs Memory Reorganisation 2.11

Note: It can take some seconds to delete the WPs, routes or flights. Please wait until the

process is completed and the confirmation “yes” resets to “no”.

* the highest accuracy is achieved when using the same co-ordinate format as most of

the GPS modules do. This is: dd°mm,mmm ( degrees; minutes and decimals of minutes

). With all other formats rounding errors can occur. ( up to 15m )

3.2 Flight Memory and Flight Analysis

In contrast to previous flight instruments the recording mode does not need to be specially

activated as each flight is automatically saved.

The flight logging system used in the Flytec 5030 GPS registers not only the flight altitude

and speed, but also logs, with the GPS receiver switched on, the time, position of the pilot in

the WGS84 coordinate system, the GPS altitude and flight speed (= air speed).

The value set in the Basic Settings/ record interval determines the time interval in seconds

after a new data record is written in the Flytec 5030 GPS's memory.

A scan rate of 2 second is advisable for tests or aerobatic flights. The factory setting is 10

seconds. In order that such a flight is logged in the flight memory, it has to be at least 3

minutes long . For the beginning of a flight the following rule applies:

The start is recognized as soon as the groundspeed reaches at least 10 km/h or if the

instrument recognizes an altitude difference of at least 30m. In each case however, the

31/53

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 52 53

Comentarios a estos manuales

Sin comentarios

Flytec 5030 v2.24 * Manual de usuario Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Flytec 5030 v2.24 *